New Industry Standards to Increase the Reliability of Drilling Operations

Autores

DOI:

https://doi.org/10.15628/holos.2019.9009

Palavras-chave:

Triangle of Normal Wear, SME, drilling dynamics, reliability

Resumo

Design engineers select drilling bits based on their professional experience and knowledge about the area of the upcoming wells. Due to the absence of widely accepted algorithms for this task, diverse performance projections can come out if prepared by different persons. By selecting bits to withstand ranges of parameters similar to the used in offset wells, less failures and longer runs can be expected. In deeper wells, a slow increase in the modes of string harmonics makes well planning complex, becoming crucial for the endurance of drilling bits to avoid resonance. Two new standards are proposed to the Oil & Gas industry in this article, created to make well planning more effective and to increase safety in selecting drilling parameters at the rig. An environment of higher drilling efficiency will result in more reliable operations and lower operational costs.

Downloads

Não há dados estatísticos.

Biografia do Autor

Dalmo S. Amorim Jr., Universidade de São Paulo

Engenheiro de Minas pela USP-SP.
Mestre em Engenharia Mineral pela USP-SP.
Doutorando em Engenharia de Petróleo no departamento de Minas e Petróleo, Universidade de São Paulo.

Otto Luiz Alcantara Santos, Louisiana State University

Professor of LSU.

Ricardo Cabral de Azevedo, Universidade de São Paulo

Professor at Departamento de Minas e Petróleo, Escola Politécnica da Universidade de São Paulo.

Referências

Amorim Jr., D. S., Hanley, C., Fonseca, I., Santos, J., Leite, D. J., Borella, A., et al. (2012). Parameter Definition Using Vibration Prediction Software Leads to Significant Drilling Performance Improvements. In G. a.-I. Brazilian Petroleum (Ed.), Rio Oil & Gas Expo and Conference, (p. 17). Rio de Janeiro, Brazil.

Barton, S. et al. (2008). Controlling Torque and Cutting Costs: Steerable Drill Bits Deliver in Latin America. In G. a.-I. Brazilian Petroleum (Ed.), Rio Oil & Gas Expo and Conference 2008 (p. 8). Rio de Janeiro: IBP.

Berg, P. V., & Tveit, Ø. S. (2016). Model for evaluating drilling efficiency based on the concept of Mechanical Specific Energy. Norwegian University of Science and Technology, Department of Petroleum Engineering and Applied Geophysics. Trondheim, Norway: NTNU.

Brandon, B.D. et al. (1992). Development of a New IADC Fixed Cutter Drill Bit Classification System. In IADC/SPE (Ed.), 1992 IADC/SPE Drilling Conference, IADC/SPE 23940, pp. 841-848. New Orleans, USA.

Bruton, G., Crockett, R., Taylor, M., DenBoer, D., Fleming, C., Ford, R., et al. (2014). PDC Bit Technology for the 21st Century. Oifield Review , 26 - 2, 48-57.

Chen, S. (2000). Patent No. US6095262A. USA.

Christian, E. (2017). Identifying the Optimum Zone for Reducing Drill String Vibrations. SPE Annual Technical Conference and Exhibition, 9-11 October, (p. 12). San Antonio, Texas, USA: Society of Petroleum Engineers.

Christoforou, A. P., & Yigit, A. S. (1997). Dynamic Modelling of Rotating Drillstrings with Borehole Interactions. (A. P. Limited, Ed.) Journal of Sound and Vibration , 243-260.

Clegg, J., Mejía, C., & Farley, S. (2019). A Paradigm in Rotary Steerable Drilling - Market Demands Drive a New Solution. SPE/IADC International Drilling Conference and Exhibition (p. 16). The Hague, The Netherlands: Society of Petroleum Engineers.

Fazaelizadeh, M. (2013). Real Time Torque and Drag Analysis during Directional Drilling (Thesis for Doctoral Degree ed.). (D. o. Engineering, Ed.) Calgary, Alberta, Canada: Faculty of Graduate Studies.

Garner, L. L. (1982). Patent No. 4359335A. USA.

Ghasemloonia, A. (2012). Vibration Analysis of a Drillstring in Vibration-Assisted Rotary Drilling: Finite Element Modeling With Analytical Validation. Journal of Energy Resources Technology , 135, 18.

Goicoechea, H. E., Buezas, F. S., & Rosales, M. B. (2019). A non-linear Cosserat rod model for drill-string dynamics in arbitrary borehole geometries with contact and friction. International Journal of Mechanical Sciences , Volumes 157–158, 98-110.

Greenhill, L., & Cornejo, G. (1995). Critical Speeds Resulting from Unbalance Excitation of Backward Whirl Modes. Design Engineering Technical Conferences (pp. 991 - 1000). Boston, MA - USA: ASME.

Huang, Z. Q., & Li, G. (2018). Failure Analysis of Roller Cone Bit Bearing Based on Mechanics and Microstructure. Journal of Failure , 18, 342-349.

Hutchinson, M. (2006). Patent No. US7140452 B2. United States.

Javanmardi, K., & Gaspard, D. T. (1992). Application of Soft-Torque Rotary Table in Mobile Bay. SPE/IADC Drilling Conference (p. 6). Louisiana: Society of Petroleum Engineers.

Jogi, P.N. et al. (2002). Field Verification of Model-Derived Natural Frequencies of a Drill String. Hostoun, USA: Amercian Society of Mechanical Engineers - ASME.

King, W. (2003). Patent No. US6612382B2. UK.

KissSoft. (2013, 03). Kadkraft Systems. Retrieved 06 06, 2018, from KISSsoft: http://kadkraft.com/wp-content/uploads/2015/06/THE-KSO-AS-1750-00-EES-Bearing-Reliability.pdf

Lee, S.S. et al. (2018). Development of a trip time for bit exchange simulator for drilling time. Geothermics , 71, 24-33.

McGehee, D. Y., Dahlem, J. S., Gieck, J. C., Kost, B., Lafuze, D., Reinsvold, C. H., et al. (1992). The IADC Roller Bit Dull Grading System. IADC/SPE Drilling Conference (pp. 819-834). Louisiana, USA: IADC/SPE.

McGehee, D.Y. et al. (1992). The IADC Roller Bit Classification System. IADC/SPE 23937 (pp. 801 - 818). Louisiana, USA: Society of Petroleum Engineers.

Moraes, L. P., & Savi, M. A. (2018, 09 07). Drill-string vibration analysis considering an axial-torsion-lateral nonsmooth model. (Elsevier, Ed.) Journal of Sound and Vibration , pp. 220-237.

Peng, W., Hongjian, N., Xueying, W., Ruihe, W., & Shuangfang, L. (2018). Research on the characteristics of earthworm-like vibration drilling. (Elsevier, Ed.) Journal of Petroleum Science and Engineering , 160, 60-71.

Rodney, P. e. (2015). Patent No. US 20150233231A1. USA.

Scott, D. E. (2005). The History and Impact of Synthetic Diamond Cutters and Diamond Enhanced Inserts on the Oil and Gas Industry.

Simmons, E. (1986, 02 12). A Technique for Accurate Bit Programming and Drilling Performance Optimization. SPE/IADC Drilling Conference . Dallas, Texas, USA.

Teale, R. (1965, March). The Concept of Specific Energy in Rock Drilling. (I. J. Abstracts, Ed.) Isleworth, Middlesex, U.K.: Mining Research Establishment.

Teodorescu, S. G. (2016). Patent No. US9238958B2. USA, The Woodlands - TX.

Downloads

Publicado

20/11/2019

Como Citar

Amorim Jr., D. S., Santos, O. L. A., & de Azevedo, R. C. (2019). New Industry Standards to Increase the Reliability of Drilling Operations. HOLOS, 6, 1–14. https://doi.org/10.15628/holos.2019.9009

Edição

Seção

ARTIGOS

Artigos mais lidos pelo mesmo(s) autor(es)

Artigos Semelhantes

<< < 1 2 3 4 > >> 

Você também pode iniciar uma pesquisa avançada por similaridade para este artigo.